A repair is offered only if the tyre is safe to keep. The hole must be in the central tread area, no wider than 6 mm, and the tyre must not have been driven flat. If any of those fail, we show you the damage and quote a replacement instead. We would rather lose a repair than send a 2,000 kg car onto the E311 on a compromised tyre.
For the background on why foam-lined tyres need a different approach, read our post on puncture repair in foam-lined tyres.
What's different on an EV
Many EV tyres carry a band of acoustic foam, often 20–30 mm thick, glued to the inner tread to absorb cavity noise. Tesla's T0 tyres, Michelin Acoustic, Pirelli Elect with PNCS, Continental ContiSilent and Hankook Sound Absorber all use it. A patch cannot bond to foam, so the foam around the puncture has to be cut back neatly to bare inner liner, the liner buffed and cleaned, and the patch applied there. Shops that skip this step and push a string plug in from outside leave a repair the foam hides, and it can leak or fail weeks later.
EV tyres are also built for heavier loads, with HL or XL ratings and reinforced casings, and that load makes a proper repair more important, not less. A string plug alone does not seal the inner liner, so air and moisture work into the steel belts, and on a heavy EV in summer heat that can lead to belt separation. We fit a plug-patch, the method tyre makers approve, so the hole is filled and the liner sealed in one piece.
When you need puncture repair
- One tyre loses 2–5 psi over a few days while the others hold
- A screw, nail or staple visible in the tread
- The TPMS warning returns days after you topped up the tyre
- A hissing sound, or bubbles when you spray soapy water on the tread
- You used a sealant kit and need a permanent fix
How we do it
- 01
Find the leak
We inflate the tyre, check it with soapy water and mark the injury, noting its position and the angle the object went in.
- 02
Take the tyre off the rim
The wheel comes off on the jacking points and the tyre is demounted, with the bead broken away from the TPMS sensor.
- 03
Inspect inside
We look for crumbled rubber, a crease from running flat, or cord damage. If any is present, the tyre is not repairable and we tell you why.
- 04
Cut back foam and prepare
On foam-lined tyres we remove a neat section of foam around the hole, buff the inner liner and apply vulcanising cement.
- 05
Plug-patch, remount and balance
The plug-patch is pulled through the injury from inside, rolled onto the liner and trimmed flush on the tread. The tyre is remounted, balanced and set to cold pressure.
Plug, patch or plug-patch: which repair we use and why
We use a one-piece plug-patch, applied from inside the tyre, for every permanent repair. Major tyre makers recommend it because it does two jobs at once: the stem fills the hole through the tread so water cannot reach the belts, and the patch seals the inner liner so air cannot escape.
A string plug pushed in from outside is quick and cheap, and plenty of petrol stations offer it. As an emergency measure to get home it is reasonable, but it does neither job properly on a modern EV tyre, and nobody can do it properly on a foam-lined tyre without seeing the inside. A patch alone, without a stem, seals the air but leaves the hole open to moisture.
If your tyre already has a string plug from somewhere else, we can usually remove it and fit a proper plug-patch in the same hole, as long as the hole is within limits.
The repairable zone and the 6 mm rule
A puncture is repairable only if it sits in the central part of the tread and is no more than 6 mm across. Anything in the shoulder, near the edge of the tread or on the sidewall is not, because those areas flex too much for a patch to stay sealed.
On a 255/45 R19 tyre that leaves a central band of roughly 150–170 mm. Screws often enter at an angle, so we judge the injury by where it exits on the inside, not only where it went in.
We also limit the number of repairs. Two per tyre is our maximum, and they must sit well apart around the circumference. Repairs that overlap or sit close together weaken the casing.
- Central tread only, never shoulder or sidewall
- Maximum 6 mm diameter
- No signs of running flat inside the tyre
- Maximum two repairs per tyre, well spaced
- Tread above 3 mm, otherwise a new tyre is usually better value
Why so many screws end up in UAE tyres
Construction. Dubai and Abu Dhabi are full of active building sites, and the roads around them collect screws, nails and metal offcuts that fall from trucks. We see clusters of punctures from Jumeirah Village Circle, Dubai South, Al Furjan, Meydan and Al Reem Island, as well as the industrial zones of Al Quoz and Mussafah.
Wide EV tyres pick them up easily, and because the cars are quiet, few drivers hear a screw ticking on the road. The first sign is usually a TPMS warning a few days later, or a soft tyre in the parking bay one morning.
A quick look at your tread after driving past a site can catch a screw before it becomes a flat. If you find one, leave it in place, check the pressure and book a repair. Pulling it out turns a slow leak into a fast one.
When replacing beats repairing
A repair is good value only when the tyre has real life left. If the tread is below 3 mm, a new tyre is often the better use of money, and we will say so even when the puncture is technically repairable.
Age matters as much as tread. A five-year-old tyre with sun cracking in the sidewall should be replaced rather than repaired, because the rubber is near the end of its safe life in UAE heat. On all-wheel-drive EVs, one new tyre may mean its partner needs replacing too, so we look at the whole axle before advising.
If replacement is the right call, we can fit a new tyre in the same visit through our EV tyre replacement service, provided your size is on the van.
